HELMETS

All helmets are $150USD to the USA and territories.
International: please EMAIL for a shipping quote and invoice.

USA customers, shipping is included in the price -
Please use the PayPal buttons below.
International Customers, please EMAIL ME for a shipping quote.
White Resin
Assembly Services



THE KHAOS IS HERE!!!

This helmet can be scaled to fit!
The examples above are of two sizes already available and read to go.
"Movie" scale (left at 1:1 scale to screen-used Mandalorian helmets) and "Ogre" scale (right - shown without ears attached)

The following measurements are the OUTSIDE DIMENSIONS

Movie-scale (1:1) Helmet:

Ear to Ear - 237mm (9.3")
Front to Back - 264mm (10.4")
Bottom to Top - 260mm (10.3")

OGRE Helmet:

Ear to Ear - 250mm (9.84")
Front to Back - 280mm (11")
Bottom to Top - 292mm (11.5")

Custom sizing is available.


Please send your Height (H), Width (W), and Depth (D). Using a straight line across these measurements, send your:
Height - from your chin to the top of your head.
Width - from ear to ear
Depth - from your nose to the back of your head

This helmet is currently only available in 3D printed parts as follows:

Printed parts - customer assembles the helmet - $125
Assembled - customer finishes (fill, sanding, painting) - $150
Finished - assembled, filled, sanded (customer paints) - $200
Painted - all of the above and painted with your color scheme - $300

A resin helmet will be made available later this year as time permits.

International, please EMAIL ME with your country and/or postal code for a quote.
Please choose
Size
Custom Size HxWxD


FOR CLARIFICATION:

Helmets made by TMA, unless otherwise noted, are hand-crafted. As such, even with careful attention to detail, some minor assymetry is to be expected.

Helmet kits come as listed with associated ears and RF stalk (if applicable), an pre-cut visor, and RF bolts and magnets (Classic helmet only. Sabine and Rebels Male RF bolt is integrated). The production base ring is removed and bottom edge sanded prior to shipping, but it is the customer's responsibility to finish any and all trimming, sanding, and installation of associated parts or to procure any other items needed for their helmet.

The visors I include can be found here: https://www.homelectrical.com/9-x-15-12-dark-green-unbound-visor.anc-3442udg.1.html. As of February 1, 2019, they are $3.49USD plus shipping to your location if you need a replacement.

If you would like a colored miror visor for your helmet, be sure to check out Kalevala Visors on Facebook!


***SPECIAL NOTES ON HELMETS***

Helmets come as shown. If assembly services are not purchased, it is the customer's responsibility to do any final trim, assembly, sanding, and painting of the helmets as desired as well as installtion of the visor and RF stalk.

If the $75 ASSEMBLY is purchased, all 2-part seams will be sanded, ancillary pieces trimmed down, visor area removed, visor fully trimmed to fit (but not installed), holes for Sabine and Classic stalks drilled, and RF stalks assembled.

If the $100 ASSEMBLY is purchased, all of the above will be done and the visor will be installed semi-permanent using high-temp hot glue. "Semi-permanent" means that the customer will be able to remove the visor at a future date if so desired. CUSTOMER ASSUMES ALL RISK WITH PAINTING IF THE VISOR IS INSTALLED!

PLEASE NOTE - Due to the nature of the casting process, some minor inconsistencies can and may occur. These include, but are not limited to, thick and/or thin spots, small bubbles, minor imperfections in the inner layer of the cast, and variations in the thickness of the casting. Even in a climate-controlled shop, a wide range of temperature and humidity variables can make a difference from casting to casting. Some minor inconsistencies that affect the EXTERIOR APPEARANCE (such as 2-part mold seams) may not be corrected prior to shipping and are usually eliminated during the trim, sanding, assembly, and painting process. This is not, however, a guarantee that every minor inconsistency will be corrected and some may still exist when you receive the helmet. Helmets with major defects will not be shipped. If a helmet with more than minor inconsistencies is received, please CONTACT ME to discuss exchange options.

Thank you for doing business with TMA!